A furnace that won't ignite, short-cycles, or trips its limit switch repeatedly needs more than a reset — it needs a technician checking the ignitor, flame sensor, and heat exchanger. Every Furnace Repair visit includes a carbon monoxide safety check as a standard part of the job, not an upsell.

Furnace failures cluster heavily around a handful of parts — ignitors, flame sensors, gas valves, and heat exchangers — and most no-heat calls come down to one of those four. We test each with a multimeter and combustion analyzer rather than replacing parts on a hunch.
What doesn't change from visit to visit.
A CO safety check with a combustion analyzer is part of every visit, not an optional add-on.
No-heat calls during cold snaps get priority routing over routine maintenance stops when temperatures drop, especially in peak winter.
You approve a fixed repair price before any part is replaced, whether it's an ignitor or a heat exchanger.
Whether the furnace runs on gas or electric heat strips, our techs are trained on both, so the fuel type never determines who gets sent.
The most common furnace failure points.
A cracked hot-surface ignitor or a flame sensor coated in carbon buildup are two of the most common no-heat causes, and both are usually same-visit fixes.
We test gas valve response and pressure output rather than replacing an expensive part on a hunch, since these parts are costly enough to warrant confirming the fault first.
A cracked heat exchanger is a genuine safety issue that can leak combustion gases into the airflow — we inspect with a camera and combustion analyzer rather than assuming based on age alone.
A furnace that short-cycles or shuts down mid-cycle often points to a tripped limit switch or failing blower — we test both before condemning the control board.
Older furnaces with standing pilots have their own failure points — thermocouples, pilot orifices, draft issues — that we're equipped to handle that newer ignition systems don't have.
Zero response from the furnace can mean a wiring fault or thermostat issue rather than the furnace itself — we rule this out early to avoid overcharging for parts you don't need.

Four steps, safety checked at every one.
Tell us what the furnace is doing and we'll route the closest technician.
A stocked truck arrives in your confirmed window ready to diagnose and often repair on the spot.
We run the safety and diagnostic checks first, then present a flat-rate quote for your approval.
Most furnace repairs are completed same-visit, with a final CO safety check before the tech leaves, backed by our labor warranty.
Recent reviews from winter heating calls.
Furnace kept shutting off every twenty minutes. The tech found a dirty flame sensor and cleaned it, been running fine for two months now.
— B. Halloran, homeowner
They caught a hairline crack in the heat exchanger during a routine repair call and walked me through the safety concern honestly, not to upsell.
— V. Ashworth, homeowner
No heat during the coldest week of the year, they got someone out same day and had it fixed within an hour, ignitor replacement.
— Q. Delrio, homeowner
Old standing pilot furnace that most companies don't want to touch anymore. They knew exactly what they were doing, thermocouple was the issue.
— E. Vantassel, homeowner

Common questions before a Furnace Repair visit.
Clicking or humming without ignition often points to the ignitor, though we always confirm with a proper resistance reading before quoting.
Yes — it can allow combustion gases to mix with breathing air, which is why we test carefully and won't run the furnace if confirmed cracked, so we take the inspection seriously and won't operate a confirmed-cracked unit.
Yes, a combustion analyzer reading is part of every Furnace Repair service, included in the visit, no extra charge.
Yes — our techs are trained on thermocouples, pilot orifices, and draft diagnostics for older systems, including thermocouple and draft-related repairs.
We prioritize no-heat situations, usually landing a same-day slot even during high-demand cold weather.
Most common parts — ignitors, flame sensors, control boards — are stocked, but rare parts may need next-day ordering to complete the repair.
We dispatch heating techs throughout Stonington and the surrounding zips — call to confirm availability.
Call +1-844-611-2875